Initial Program Loader: Difference between revisions
(Credits to SilverSpring for the info) |
CelesteBlue (talk | contribs) No edit summary |
||
| Line 1: | Line 1: | ||
IPL is loaded by [[PRE-IPL]]. | |||
= Tools = | |||
[https://github.com/zecoxao/ipltool] | |||
= IPL Boot Sequence = | = IPL Boot Sequence = | ||
The decrypted IPL is composed of 3 parts: Part1 - the 'loader', Part2 - 'main.bin', and Part3 - the 'payload'. | |||
The decrypted IPL is composed of 3 parts: | |||
Part1 - the 'loader', Part2 - 'main.bin', and Part3 - the 'payload'. | Part1 is plaintext MIPS code, Part2 is gzip compressed, and Part3 is again encrypted (from 2.60 onwards, parts 2 & 3 are further encrypted again). | ||
Part1 is plaintext MIPS code, Part2 is gzip compressed, and Part3 is | |||
again encrypted (from 2.60 onwards, parts 2 & 3 are further encrypted | |||
again). | |||
== Part1 IPL (the loader) == | == Part1 IPL (the loader) == | ||
One of the first things Part1 IPL does is reset the main CPU. | One of the first things Part1 IPL does is reset the main CPU. | ||
After reset the | |||
all (the 0x1FC00000 address range is then remapped to the 4KB RAM | After reset the PRE-IPL mask ROM device is no longer mapped to memory at all (the 0x1FC00000 address range is then remapped to the 4KB RAM mentioned above to be used for the ME reset vector). This is why the PRE-IPL is no longer accessible once the IPL has booted. | ||
mentioned above to be used for the ME reset vector). This is why the | |||
Part1 IPL does some very basic hardware inits and decompresses the gzipped Part2 IPL (main.bin) to address 0x04000000 (still in EDRAM). | |||
does some very basic hardware inits and decompresses the gzipped Part2 | |||
IPL (main.bin) to address 0x04000000 (still in EDRAM). Part1 IPL then | Part1 IPL then jumps to the entry address of main.bin (0x04000000) to initialize the hardware. | ||
jumps to the entry address of main.bin (0x04000000) to | |||
hardware. | |||
== Part2 IPL (main.bin) == | == Part2 IPL (main.bin) == | ||
Part2 IPL (main.bin) is responsible for initializing the PSP hardware. | |||
Part2 IPL (main.bin) is responsible for | |||
It has copies of it's own driver libraries similar to the drivers found | It has copies of it's own driver libraries similar to the drivers found in the firmware (including: sceNAND_Driver, sceDDR_Driver, sceIdStorage_Service, sceSYSREG_Driver, sceSYSCON_Driver, sceGPIO_Driver, sceClockgen_Driver, & sceI2C_Driver). Some of the initialisation of the hardware depends on data stored in IDStorage leaves (for example leaves 4, 5, 6). Note this is where TA082/086 motherboards 'brick' on 1.50 firmware. The clockgen hardware was changed on TA082/086 motherboards so the functions used to initialise it does not recognise the new hardware. And because part of the initialization depends on data stored in leaf 5, simply by invalidating leaf 5 (by corrupting the header), the initialization is skipped allowing the firmware to continue to boot. | ||
in the firmware (including: sceNAND_Driver, sceDDR_Driver, | |||
sceIdStorage_Service, sceSYSREG_Driver, sceSYSCON_Driver, | After initializing the hardware (including the DDR RAM), Part2 IPL decrypts Part3 IPL (the payload) and loads it to address 0x08400000 (which is located in normal DDR RAM now that it has been initialised). | ||
sceGPIO_Driver, sceClockgen_Driver, & sceI2C_Driver). Some of the | |||
initialisation of the hardware depends on data stored in | It then jumps to the entry address of the Part3 IPL (0x08400000) to boot the firmware. | ||
(for example | |||
'brick' on 1.50 firmware. The clockgen hardware was changed on TA082/086 | |||
motherboards so the functions used to initialise it does not recognise | |||
the new hardware. And because part of the | |||
stored in | |||
the | |||
After | |||
decrypts | |||
(which is located in normal DDR RAM now that it has been initialised). | |||
It then jumps to the entry address of the Part3 IPL (0x08400000) to boot | |||
the firmware. | |||
== Part3 IPL (the payload) == | == Part3 IPL (the payload) == | ||
TODO | TODO | ||
Revision as of 00:59, 18 February 2020
IPL is loaded by PRE-IPL.
Tools
IPL Boot Sequence
The decrypted IPL is composed of 3 parts: Part1 - the 'loader', Part2 - 'main.bin', and Part3 - the 'payload'.
Part1 is plaintext MIPS code, Part2 is gzip compressed, and Part3 is again encrypted (from 2.60 onwards, parts 2 & 3 are further encrypted again).
Part1 IPL (the loader)
One of the first things Part1 IPL does is reset the main CPU.
After reset the PRE-IPL mask ROM device is no longer mapped to memory at all (the 0x1FC00000 address range is then remapped to the 4KB RAM mentioned above to be used for the ME reset vector). This is why the PRE-IPL is no longer accessible once the IPL has booted.
Part1 IPL does some very basic hardware inits and decompresses the gzipped Part2 IPL (main.bin) to address 0x04000000 (still in EDRAM).
Part1 IPL then jumps to the entry address of main.bin (0x04000000) to initialize the hardware.
Part2 IPL (main.bin)
Part2 IPL (main.bin) is responsible for initializing the PSP hardware.
It has copies of it's own driver libraries similar to the drivers found in the firmware (including: sceNAND_Driver, sceDDR_Driver, sceIdStorage_Service, sceSYSREG_Driver, sceSYSCON_Driver, sceGPIO_Driver, sceClockgen_Driver, & sceI2C_Driver). Some of the initialisation of the hardware depends on data stored in IDStorage leaves (for example leaves 4, 5, 6). Note this is where TA082/086 motherboards 'brick' on 1.50 firmware. The clockgen hardware was changed on TA082/086 motherboards so the functions used to initialise it does not recognise the new hardware. And because part of the initialization depends on data stored in leaf 5, simply by invalidating leaf 5 (by corrupting the header), the initialization is skipped allowing the firmware to continue to boot.
After initializing the hardware (including the DDR RAM), Part2 IPL decrypts Part3 IPL (the payload) and loads it to address 0x08400000 (which is located in normal DDR RAM now that it has been initialised).
It then jumps to the entry address of the Part3 IPL (0x08400000) to boot the firmware.
Part3 IPL (the payload)
TODO